Electrolux Dishwasher Displays an Error Code – Causes and Solutions

Issue

If your Electrolux dishwasher displays an error code, shows an "i" code followed by numbers, emits beeps, or flashes warning lights, the dishwasher has detected an issue that requires attention.

Electrolux dishwashers use built-in diagnostics to monitor key functions such as water intake, drainage, water levels, heating, and leak protection. When a problem is detected, the dishwasher may stop the programme and display an error code to help identify the cause.

Typical signs:

• An error code appears on the display
• The dishwasher beeps repeatedly
• Warning lights flash
• The wash programme stops unexpectedly
• The dishwasher does not fill with water
• The dishwasher does not drain properly
• The dishwasher does not complete the cycle

Applies to

• Electrolux Dishwashers

Resolution

Start by checking the error code displayed on your dishwasher. In many cases, the issue can be resolved by following the troubleshooting steps associated with the specific code.

Error code i10, i11, AL5, C1 or 1 beep

Water supply problem.

The dishwasher is not receiving enough water or cannot detect the incoming water supply.

See: Electrolux dishwasher displays error code i10, i11, AL5, C1, beeps once, or the warning light flashes once

Error code i20, C2, F2, AL6 or 2 beeps

Draining problem.

The dishwasher cannot remove water from the tub within the expected time.

See: Electrolux dishwasher displays error code i20, C2, F2 or AL6, or beeps twice, not draining

Error code i30 or 3 beeps

Water leak detected.

The anti-flood protection system has detected water where it should not be.

See: Electrolux dishwasher displays error code i30, beeps 3 times, or the warning light flashes 3 times

Error code i40, i43, i44 or 4 beeps

Water level sensing problem.

The dishwasher cannot correctly measure or monitor the water level.

See: Electrolux dishwasher displays error code i40, i43 or i44

Error code i50

Wash motor or circulation system problem.

The dishwasher has detected an issue affecting water circulation during the wash cycle.

See: Electrolux dishwasher displays error code i50

Error code i60, i61, i69 or i6C

Heating problem.

The dishwasher is not heating the water correctly or cannot reach the required temperature.

See: Electrolux dishwasher displays error code i60, i61, i69 or i6C

Error code iF0, iFo or iF1

Water level problem.

The dishwasher has detected an abnormal water level condition.

See: Electrolux dishwasher displays error code iF0, iFo or iF1

If your error code is not listed

Use the search function on the Electrolux Support website to find information about your specific dishwasher error code or symptom.

Important

Error codes do not always indicate a component failure. Some codes can be triggered by temporary conditions such as low water pressure, blocked filters, drainage restrictions, or a recent interruption to the power supply.

Before troubleshooting, make a note of the full error code displayed.

When Is It a Genuine Fault?

There may be a fault with the dishwasher if:

• The same error code repeatedly returns
• The dishwasher cannot complete any programme
• The error appears immediately after starting a cycle
• Water is leaking from the dishwasher
• The dishwasher does not fill, heat, wash, or drain correctly
• The appliance displays multiple fault codes

In these situations, there may be a fault with a sensor, pump, heating system, electronic control system, or associated components.

Book Service

If your Electrolux dishwasher continues to experience problems, our specially trained technicians can quickly identify the cause and help resolve the issue.

Whether your appliance is in or out of warranty, we're here to guide you to the right repair solution.

Book a repair service online

Cause

Electrolux dishwashers continuously monitor important operating functions throughout each wash cycle. When the appliance detects abnormal conditions, it generates an error code to help identify the affected system.

The most common causes are:

• Water supply issues
• Blocked filters or drainage systems
• Water leaks
• Water level sensor problems
• Circulation pump faults
• Heating system issues
• Temporary electrical interruptions
• Electronic control system faults

The error code helps narrow down the cause and directs you to the most relevant troubleshooting steps.

FAQ – Electrolux Dishwasher Error Codes

What does an i-code mean on my Electrolux dishwasher?

An i-code indicates that the dishwasher has detected a specific fault or operating issue.

Why is my dishwasher beeping?

The dishwasher may beep to alert you to an active error code or warning condition.

Can I reset my dishwasher after an error code appears?

Yes. Disconnect the power supply for 30 to 60 seconds, reconnect it, and check whether the error returns.

Why are the lights flashing on my dishwasher?

Some dishwasher models use flashing LEDs instead of a display screen to indicate errors.

Do error codes always mean a repair is needed?

No. Some error codes can be caused by temporary issues such as blocked filters, drainage restrictions, or water supply problems.

When should I book a repair?

Book a repair if the error remains after completing the recommended checks or if the dishwasher cannot operate normally.